MOTOROLA ASTRO SABER III 800MHZ RADIO H04UCH9PW7AN (No Charger, NO Battery) Motorola Astro SABER III radio. MOTOROLA ASTRO SABER III UHF 450-512mhz LAPD MODAT pre-programmed all FRS/GMRS NTN4595 Battery for MOTOROLA Astro Saber I II III 1 2 3. NTN4593 NTN4594 NTN4595 Battery for. Eagle Software For Pcb Design.

This article includes a, but its sources remain unclear because it has insufficient. Please help to this article by more precise citations. (January 2013) () () The Motorola Saber is a product series of The Saber is a commercial radio that was developed for the sometime around 1989. The Saber is widely recognizable by thin, sleek design compared to other radios at the time. Despite the fact that the Saber was originally marketed to the military, many agencies and realized the benefits of the Saber and Motorola soon had a much larger customer base for the radio than they expected. Contents • • • • Saber Conventional [ ] The first Saber line was Conventional operation only. The conventional Sabers were capable of PL/DPL and were capable.

The Saber came in 4 different flavors; I, II, III, and IE. The Model I has 12 channels in 1 zone. The IE was a Model I with an additional zone of 12 channels, 24 in all. The Model II is either capable of 4 zones of 48 or 10 zones of 120 channels. This is dependent on the memory. It has a display which was capable of 5 characters if you have the 120 channel 2 KB version or the basic zone/channel display for the 48 channel version. It came with 3 to access menu options.

Model III was basically a model II with a full DTMF keypad. Systems Saber [ ] The Systems Saber added analog operation, direct access to functions via the keypad (on the Systems Saber III), and increased to a then-unheard of 255 conventional channels. The Systems Saber also increased the number of channels per zone to sixteen and added the ability to reprogram the function of many of the controls. ASTRO™ Digital Saber [ ] The Astro Saber was introduced in the mid 1990s and was a technologically advanced and state of the art at the time. The Astro Saber is feature packed Not only is it capable of IMBE Digital and conventional analog on a per channel basis, but also some models are 12.5/25 kHz per channel as well. This makes some Astro Saber Narrow Band compliant.

Model I has 16 channels, in 1 zone. No display or keypad. Model II has 16 channels in 16 zones and a 14 character alphanumeric backlight display. It came with 6 softkey buttons to access an advanced menu. Model III was basically a model II with a full DTMF keypad. References [ ].

Astro Portables Astro Portables General Information Most of this information is for the Astro Saber, but since the XTS3000 and its family are programmed by the same RSS, a lot of the information will be relevant for it too. All these radios use a standard SMA connector for the antenna. The radio end is a male. Be sure that you use a high quality adapter if you are going to convert from the SMA to something else. There are some cheap adapters that have a recessed center pin on the female side. This causes problems since the center pin on the radio may not make contact and you will be transmitting into an open (bad). The radio uses a third generation keyloader, there is a retro kit to upgrade the DES-XL key loader, and the data in and out pins are different.

Only keyloaders with a model suffix DX or later will properly keyload an Astro, while BX & CX (as well as DX) models will work fine with a regular Saber. For keyloading, you use the same cable as a regular Saber, TKN8506, and the pinout is available. The part number for the HHCH for the XTS3000 Vehicular Adapter (XTVA) may be PLN7737A (unconfirmed). Here you can find the model breakdown chart.

Note that it is the same as the one for the mobiles, except for the available power levels and the 'H' at the beginning of the model number to denote portable. A listing of the flash upgrade options can be found. You may also want to look at the. Take a look at the for the Astro Saber. The programming cable for the XTS3000 and XTS3500 is the same as the other Jedi radios, RKN4035A, and its pinout can be found. You may also want to take a look at the RKN4046A.

Albo Ingegneri Cagliari Pdf Files. This cable is for the Astro Saber and Saber Si. This cable is made up of the following parts: Reference Part Number Description 1 0984538E03 Receptacle, 25 Pos 2 1580349B36 Housing, Connector 3 Cable, 5 Conductor 4 0180754R26 Plug Assembly 5 4210217R24 Strap, Tie 6 3880373L24 Protective Cap 7 0410058B12 Washer, Nylon 8 0960113A07 Connector and Cable C1 2184008H06 Capacitor, 33 nF R1 0611009C59 Resistor, 2.7 kohm R2 0611009C73 Resistor, 10 kohm By the way, if you thing you can make yourself a cheap cable by just ordering part number 0960113A07, well, forget it. The current list price for that item is $166US.

Astro Saber and LAPD There seems to be a number of people interested in the Astro Sabers that the LAPD uses. This section will try and answer many of those related questions. First, the radio that the LAPD is using is the H04SDH9PW7AN. You are probably better off not trying to get Motorola to flash your Astro Saber 'just like LAPD's'. Motorola considers FlashCodes 840101-8F0000-4 and now 500-7 to be RESTRICTED. If you send in a radio to the depot for service with one of these flash codes, they will only send it back with H35 and you have to buy any upgrades you want for the radio. If you do try to get that flashed into your radio, Motorola security may get involved and start asking questions.